News

    Recently, the 500-ton four-column vertical aluminum scrap briquetting equipment of Starshine Machinery has been put into operation and commissioned in a large-scale scrap aluminum recycling and processing plant. The whole production line is equipped with double conveying and feeding structure, which can automatically process loose waste materials such as aluminum shavings and aluminum powder.     The Metal Chips Briguetting Machine adopts the grading pressurization forming process. The air inside the debris is discharged in the pre-pressing process. The main oil cylinder is 500 tons of constant pressure extrusion and synchronous separation of cutting oil. The waste liquid can be recycled centrally. The wear-resistant alloy lining die ensures the stability of long-term high-pressure operation, the density of the produced aluminum blocks is uniform, the storage space is reduced by more than 75%, there is no dust loss in transshipment, and the smelting recovery premium is obvious.     This Metal Briquetting Press supports 24-hour continuous operation, with an hourly processing capacity of 3.2 tons. Only one person is required to be on duty. The closed processing conditions meet the requirements of environmental protection verification. The person in charge of the plant said that the qualified rate of one-week trial production of the equipment reached 100%, and the follow-up plan was to add the same type of units to increase the annual disposal scale of scrap aluminium to more than 20000 tons.

    New 500-ton Metal Briquetting Press is being containered and will be shipped to Japan.         This Hydraulic Briquetting Machine is the core equipment for metal processing waste treatment. Its nominal pressure is 500 tons, and the system pressure is usually up to 25 MPa. It can exert extremely strong vertical extrusion force.       The loose waste materials such as cast iron scraps, steel scraps, aluminum scraps and the like can be cold-pressed into a high-density round cake with the diameter of 120 to 140mm, the weight of a single block is about 4 to 5kg, the density is as high as 5t/m ³, and the volume is reduced to 1/5 to 1/10 of the original volume.     The hydraulic cold pressing process is adopted without heating and additives, which not only ensures the purity of metal materials, but also synchronously deoiling in the pressing process, separating cutting fluid and improving the recovery value. Single shift (8 hours) production capacity can reach 6-7 tons, equipped with PLC automatic control system, low failure rate, stable operation.   Are you interested in our Metal Chips Briguetting Machine?  

    Recently, a 1000-ton hydraulic metal shear (Gantry Shear) has been put into operation at the customer's site in Singapore. With its excellent mechanical properties and highly integrated automation control, the equipment provides a scientific and efficient solution for the treatment of large quantities of light and thin scrap metals (Light Melting Scrap).   The involvement of this scrap metal shear directly affects the profit margins of scrap metal recyclers: 1. Greatly reduce logistics costs: The original scrap metal pile has a very low specific gravity. The bulk specific gravity of the scrap can be increased from 0.2 t/m ³ to more than 0.9 t/m ³ after treatment by the gantry shears. This means that the loading capacity of the same transport vehicle can be increased by more than 300%, which greatly saves transportation and storage costs. 2. Upgrading of product grade: The market price of scrap steel (such as sheared materials and heavy scrap) after shearing and impurity removal is much higher than that of unprocessed bulk materials, which directly increases the gross profit margin of recycling enterprises.       The landing of this 1000-ton gantry shear in Singapore not only improves the physical efficiency of local scrap metal processing, but also reflects the deep excavation of the value of resource regeneration by industrial manufacturing. Through the combination of precision mechanical design and intelligent hydraulic system, the equipment is becoming an indispensable "heavy weapon" in the field of circular economy in Southeast Asia.  

    The last batch of Metal Chip Briquetting Machine in 2025 has been loaded, which is customized by our company for a scrap steel recycling enterprise and will soon be delivered to the customer's production site.     The customer is mainly engaged in scrap steel shearing and recycling. Before that, the volume of loose metal chips was bulky, the transportation cost was high and the melting loss rate was high. This metal briquetting press is selected for its three core advantages: the horizontal open bin does not need additional lifting equipment, and the volume of 0.5-2m ³ is suitable for batch feeding; the 100-300 tons hydraulic pressure can achieve 4-6 times volume compression, and the density of scrap iron cake can reach 5.5g/cm ³; the PLC control system supports unattended operation and matches the local operation and maintenance conditions.      After the hydraulic briquetting machine is put into operation, it is expected to help customers reduce transportation costs by 30% and reduce smelting loss rate by 12%. This shipment also provides an efficient chip compression solution for the Central Asian steel scrap processing market.    This hydraulic press is one type of necessary aluminum recycling machineAny interests in our Aluminum Briquette Machine?Welcome to consult at anytime.  

This Metal Baler is mainly designed to compact scrap metal into circular blocks. It has been successfully installed in the customer's factory and has undergone preliminary testing.   This type of Scrap Metal Baler, as our newly developed and designed equipment, is specifically created for the recycling and processing of waste metals. It can be widely applied to the pressing operations of scrap iron, scrap aluminum, and various metal scraps and other waste metals, and can pack these waste metals into regular circular cylindrical blocks. This equipment innovatively adopts a dual-motor and dual-pump driving configuration, significantly improving the running speed, and can efficiently compress the waste metal materials into circular blocks, thereby achieving the efficient recycling and utilization of waste metal materials.   The Metal Baler Machine has a number of outstanding advantages: 1. High density compression characteristic. 2. Convenient operation performance. 3. Stable mass structure.   Are you interested in this type of metal baler machine?  

With the rapid development of industrialization, manufacturing, mechanical processing, automobile manufacturing, electronics and electrical appliances and other industries have produced a large amount of metal scrap in the production process, in which copper and aluminum scrap occupies a considerable proportion. These fine metal chips not only occupy a lot of storage space, but also easily cause loss in handling, storage and transportation because of their loose state, which brings many inconveniences and economic losses to enterprises. Traditional treatment methods are often simple accumulation or extensive smelting, the former is inefficient and has potential safety hazards, while the latter has high energy consumption and metal recovery is difficult to guarantee. In this dilemma,Metal Briguette Machine came into being, which uses innovative technology to compress loose and disorderly copper and aluminum scrap into high-density cakes, fundamentally changing the disposal pattern of metal scrap.   Metal Chip Briguetting Machine, also known as Briquetting Press, is a common equipment in metal processing, scrap metal recycling and casting industries. Its core function is to press loose metal chips into high-density cakes under high pressure and cold pressure, which is convenient for subsequent storage, transportation and smelting recovery.  

New Q08-1000 Crocodile Shear is being containered,will be shipped to India,and help our customer to deal with steel shearing in his factory.   Compare with a mechanical transmission type shearing machine,this alligator shear has the advantages of small volume, light weight, small inertia, low noise, stable action and the like, is safe to operate and use, is easy to realize the manual and automatic functions of the shearing machine, is convenient and simple to operate and control, easy to realize overload protection.   This metal shear is mainly used in the waste material recycling and processing industry and small and medium-sized steel plants. It can be used for cold shearing of scrap metals with various section shapes, such as round steel, square steel, channel steel, angle steel, I-beam, steel plate, steel pipe, etc. It is also suitable for fixed-length cutting of various steel products in rolling mills, and can also be used for shearing of automobile parts in scrap automobile dismantling plants.  

This Scrap Metal Baler will be shipped to India to participate in the recycling of scrap steel plates at the customer's factory.   There are many reasons why customers choose our side-push type Metal Baler: 1. Stable discharge without damage to the lump: the lump is pushed out at a uniform speed by the horizontal thrust, so as to avoid gravity falling when turning the bag or extrusion friction when pushing out, so as to keep the shape of the lump complete and the density uniform, and reduce the risk of loose bales. 2. Continuous operation and high efficiency: the action of pushing the package can be connected with the compression cycle, without additional adjustment of the angle of the equipment or waiting for the package to fall off. After a single cycle, the package can be pushed out quickly, which is suitable for batch continuous production. 3. The adaptation scenario is more flexible: it supports multiple directions such as side push and forward push, and can be stacked with conveyor lines, material frames or directly on the ground without reserving too high vertical space. It is more suitable for small-sized factory buildings or multi-equipment linkage scenarios.   Feel free to contact if any interests in our Metal Baler Machine.  

Today, we successfully loaded and shipped an entire container of high performance Hydraulic Briquetting Machine. Each unit is now on its way to international customers, ready to turn waste into a valuable resource.   How does our Metal Briguette Machine usually work? In terms of a common working process, the material is firstly added into a large bin above a feeding device of a cake press; then a feeding cylinder moves forward to feed the material into a die, and then the feeding cylinder returns and resets; a sub cylinder drives a piston rod of a main cylinder and a punch to rapidly press down, and when the punch enters a die cavity, the sub cylinder is transferred to the main cylinder to slowly press down, so that the material in the die is pressed into high-density cakes by high pressure; After that, the main cylinder rises slightly (the punch does not go out of the die), and the block pushing cylinder retreats to drive the slider to retreat to the position where the cake can be pressed out; the main cylinder descends quickly to press the pressed cake out of the die cavity, and the block pushing cylinder drives the slider to move forward to push the cake out of the cake, and resets at the same time; finally, the sub cylinder drives the piston rod of the main cylinder and the punch to rise to complete an action cycle and enter the next cycle. (The screw feed can also be used instead of the feed cylinder) This Metal Chips Briguetting Machine is one of our most popular peoducts,are you interested in?

This Scrap Metal Baler is specially customized for customers to handle long scrap steel shavings. It occupies a small area and is easy to operate. This Metal Baler can be operated by electrifying. It can quickly compress the recycled scattered scrap metal into "standard baling blocks", which can be loaded by 30% -50% more during transportation.   This Metal Baler Machine is suitable for handling the following materials: Waste small household appliances shell (such as electric kettle metal shell, rice cooker base metal parts), waste hardware (small wrenches, screwdrivers, nails/screws after batch collection), waste bicycle/electric vehicle small parts (such as car bars, pinions, pedals), waste door and window hardware (hinges, handles), waste medical equipment small metal parts (such as needles, small stainless steel). Compliance processing is required) and so on.   This kind of material is small in single volume but scattered in quantity, which is convenient for classification, counting and centralized recovery after packaging, so as to avoid secondary scattering after sorting.

Our Metal Briquetting Press is powerful helper in today's metal scraps recycling industry.It is good at pressing loosen metal chips such as aluminum chips,copper slags,swarf,steel turninigs...   The Metal Briguette Machine is usually hydraulically driven. A material is firstly adde into a large bin above a feeding device of a cake pressing machine, a feeding cylinder move forward to feed that material into a die, and then the feeding cylinder returns to reset; And then that main cylinder slightly rise, the block pushing cylinder retreat to drive the slide block to retreat to the position where the cake block can be pressed out, the main cylinder rapidly descends to press the pressed cake block out of the die cavity, the block pus cylinder drives the slide block to advance to push out the cake block, and meanwhile, the block pushing cylinder resets, and the sub cylinder drives the piston rod of the main cylinder and the punch to rise to complete an action cycle.   Any interests in our Hydraulic Briquetting Machine,please feel free to leave your message.  

New Heavy Duty Metal Shredder is ready for our domestic customer,for dealing with scrap aluminum turnings before being briquetted.   The main materials suitable for Metal Scrap Crusher include： • Metal shavings/chips: shavings of ferrous metals such as steel, iron, and cast iron, as well as shavings of non-ferrous metals such as aluminum, copper, zinc, and magnesium. • Small and medium-sized metal waste: short-cut bars, tubes (such as round steel, copper tubes, aluminum tubes), and scraps of plates and sections (such as steel plates, iron sheets, aluminum sheets, iron wires). • Others: Scrap small hardware (iron nails, screws, nuts), metal mesh, aluminum cans, etc. Some can handle metal waste with a small amount of oil stains and coolant.   After being shredded by our Metal Shredder, these materials can reduce their volume, facilitate transportation and storage, and provide convenience for subsequent processes such as smelting and recycling. They are widely used in industries such as metal recycling and processing, mechanical manufacturing, and smelting.  

    One more Metal Briguette Machine is ready,it's powerful presssing ability helps our customers to make scrap meta chips into recycled blocks to exchange money.     Metal Briquetting Press plays an important role in the reduction, recycling and reuse of metal scrap, serving a wide range of industrial sectors that generate metal scrap. They not only conserve resources but also meet the requirements of environmental protection and sustainable development. Metal Chips Briguetting Machine has a wide range of applications in the following fields: 1. Machining industry: Handling iron shavings, steel shavings, etc. generated by lathes, milling machines, etc., reducing storage and transportation costs. 2. Automotive manufacturing and repair: Processing metal scrap generated during production and repair, in compliance with environmental protection requirements. 3. Aerospace and shipbuilding: Recycling high-value metal scrap (such as titanium alloys and aluminium alloys) to improve material utilisation rates. 4. Metal recycling and regeneration: Compressing and dispersing scrap to improve recycling efficiency and economic benefits. 5. Casting and forging industry: Pressing scrap into briquettes for direct re-melting in furnaces, reducing burn loss. 6. Hardware products industry: Recycling and processing scrap to achieve resource and reduce procurement costs.

    Our new 360T Hydraulic Briquetting Machine is ready,for our Brazilian customer to recycle waste aluminum chips.The chips will be coacted into cakes for easily poured into the furnace.     Our Metal Chips Briguetting Machine with good market both domestic and overseas...     Aluminum Briquette Machine is mainly used for the scattered, fluffy scrap aluminum chips compressed into a higher density cake (or block), easy to transport, storage and subsequent recycling, the application of the industry is mainly concentrated in the production of a large number of scrap aluminum chips and the need for recycling of aluminum resources in the field of processing, such as: automobile manufacturing and parts processing industry, machinery manufacturing and metal processing industry, aerospace and military industry, aluminum processing and recycling industry. Aluminum products processing and recycling industry...     Feel free to contact if any interests in our mchines.Besides briquetting machines,our products cover metal balers,metal shears,metal shredders...

    New Steel Shredder is ready!This machine will be shipped for shredding steel turnings in our cuatomer's factory.     Many of our clients are steel manufacturers. During the steel processing, they often generate waste materials in the form of steel chips, which require specialized machines to process and recycle.Our Steel Scrap Shredder with good market and repuattion among these customers.     Steel Scrap Shredder Machine is a specialized equipment for processing materials such as metal shavings and chips, which are processed into a form that is easier to recycle, transport or reuse through shredding, shearing and other actions. It is applicable to a wide range of materials, generally including:Cast iron shavings,Carbon steel / low alloy steel shavings,Stainless steel shavings,Aluminum and aluminum alloy shavings,Copper and copper alloy shavings: including copper, brass, bronze and other processing of chips, shredding can reduce transportation costs,Magnesium alloy, zinc alloy and other small shavings or chips,Metal shavings with a small amount of oil,Mixed with a small amount of non-metallic impurities in the debris...

    The Scrap Metal Crusher is a kind of machinery used for crushing and shredding the scrap metal chips, so as to facilitate subsequent recycling and processing.     The main method of this Heavy Duty Metal Shredder is to use dual-axis independent drive. Two sets of cutter discs are used to shear each other, and through actions such as shearing, tearing and squeezing, the size of the materials is reduced. The materials enter the crushing box through the feeding system. The two axes move relative to each other, exerting combined actions such as tearing, squeezing and shearing on the materials, and crushing the materials into small pieces.      By setting transmission mechanisms on both sides of the chip box, each transmission mechanism drives a pair of working rollers to rotate in opposite directions to achieve the pulling or dragging of the wood chips. Combined with the misaligned pulling edges, it realizes the tearing of metal wood chips. This enables the wood chips to be uniformly and rapidly torn and fed into the discharge bin. If you have long scrap metal turnings but have no ideal to deal with,you can shoose our Metal Shredder.

    Today,combined system of Heavy Duty Metal Shredder and Metal Briguette Machine will be delivered.     Some of our factory customers, especially during the production process, generate a lot of long metal shavings. How can we turn these waste metals back into cash?     If your metal shavings are short,you can press diretly by our briquetting press,we have vertical and horizontal type machines,can meet your different requirements.But if your metal shavings are too long,it will be hard to be pressed,so we recommend our SSJ series metal shredder to crush shavings into appropriate size,for better briquetted later.The combination of Metal Shredder and Metal Chips Briguetting Machine is a highly efficient solution in the field of metal scrap processing. Through the process of “crushing - compaction”, the two have significant synergistic advantages in terms of improving recycling efficiency and reducing processing costs.     If you're also worried how to recycle long scrap metal shavings,you can feel free to contact us for appropriate solution for all your requirements.

    This Heavy Duty Metal Shredder will be shipped,and will be used to deal with scrap iron shavings shredding,for better briquetting process.     Our Iron Scrap Shredder Machine is good at crushing different types of metal scrap turnings,such as iron turnings,aluminum turnings,steel turnings...and so on.This model Metal Shredder is usually used before our briquetting press,for crushing long turnings into small pieces,it's helpful for better briquetting.     In metal processing and manufacturing enterprises, such as iron and steel mills, machinery manufacturers, automobile manufacturers and shipyards, etc., the production process will produce a large number of metal shavings, edges and scraps and other waste, metal shavings shredder can be crushed, torn and compressed to facilitate the subsequent recycling, not only to reduce the waste area, improve transportation efficiency, but also to achieve resource reuse and reduce the cost of raw materials.   Do you want this sheredder?Please feel free to contact or lead your message on our website.

    This Hydraulic Briquetting Machineis one of the most popular machines in our factory,this machine is mainly used to deal with scrap metal chips,slags,shavings,turnings...For different material,we can provide customized solutions to meet your requirements.Large hydraulic power can make scrap chips into different metal chips cakes.     Metal Chip Briguetting Machine is suitable for many scrap metal materials, including cast iron chips, steel chips, iron chips and so on. These are common wastes in the metal processing industry, and the metal chip cake machine can compress them into cake pieces, which is easy to recycle and reuse, reduce transportation cost and storage space, and improve the recovery rate of metal at the same time.     Briquetting Press also has a good pressing effect on non-ferrous metal chips: such as aluminum chips, copper chips, zinc chips, lead chips, titanium chips, stainless steel chips and so on. Non-ferrous metals usually have high value, and their crumbs are compressed into cakes by metal crumb cake machine, which helps to store and transport them better in the recycling process and improve the efficiency of resource utilization.  

        Today,we have tested waste tire wire on Y83-2500 Metal Briguette Machine,for making tire wire briquettes according to our customer's requirements.    The pressing process for tire wire needs enough pressure (usually hundreds of tons of hydraulic pressure) to make the steel wire tight bite, but too much pressure will lead to equipment overload, and even deformation of the mold; pressure is not enough, then the steel wire cake is loose and easy to break.     Part of the process needs to be combined with heating (such as heating the wire to 200-300 ℃) to reduce the rubber viscosity, but improper temperature control will lead to oxidation of the wire, affecting the metal properties, and high-temperature environment on the corrosion resistance of the equipment requires more.     The Metal Briquetting Press usually has a strong pressure output, which can compress the tire steel wire into a cake in a short time. For example, some large Hydraulic Briquetting Machine adopts cartridge type hydraulic valve set, which can handle large flow and high pressure, and can easily deal with a large amount of tire steel wire compression cake work, greatly improving the production efficiency.